How to Balance Radiators

Home › Guides › How to Balance Radiators

Balancing a radiator means adjusting its lockshield valve so hot water spreads evenly around the house instead of rushing to the nearest radiators. The radiators nearest the boiler heat first and take the flow; the ones furthest away stay cold. Work from the boiler outwards, closing each lockshield to a quarter turn and then opening it until the flow and return pipes differ by about 12°C. The job is methodical rather than complicated, and it needs no more than a bleed key, a spanner and a thermometer.

How to tell if your radiators need balancing

Uneven heat is the sign: some rooms are warm while others stay cold, radiators near the boiler get hot fast, and radiators at the far end of the house lag behind or never warm up properly. A quick test confirms it: close one valve on every hot radiator and leave the cold radiator valves fully open. If the cold radiators get hot, the system needs balancing. If they stay cold, the problem is something else, such as trapped air, a stuck valve or sludge, and balancing will not fix it. Bleed the radiators first either way, since trapped air gives false readings: our guide How to Bleed a Radiator covers that step.

What you need

  • A radiator bleed key, for bleeding every radiator before you start.
  • An adjustable spanner or lockshield valve adjuster, to turn the metal spindle once the plastic cap is off. Some lockshields need pliers or a hex key instead.
  • A digital or infrared thermometer, to measure the flow and return pipe temperatures.
  • A notepad, to write down the order in which the radiators heat up.

Check the boiler pressure before you start: it should sit between 1 and 1.5 bar. Top it up through the filling loop if it is low, and call a heating engineer if it keeps dropping, since that points to a leak rather than a balancing problem.

How to balance radiators step by step

  1. Turn the heating off and let the radiators cool down completely. Cold radiators give a clean starting point.
  2. Bleed every radiator with the bleed key, holding a cloth under the valve. Trapped air creates cold spots and throws off your temperature readings.
  3. Open all the valves fully. Turn every thermostatic radiator valve to its maximum setting and every manual valve anti-clockwise. Remove the plastic cap from each lockshield valve and turn the metal spindle anti-clockwise until it stops.
  4. Turn the heating back on with all thermostats and valves fully open. Walk round the house and note the exact order in which each radiator heats up. The radiator nearest the boiler heats first and the furthest away heats last: that order is your balancing sequence.
  5. Turn the heating off and let the radiators cool again.
  6. Go to the radiator that heated first. Turn its lockshield valve clockwise until it is fully closed, then open it anti-clockwise by just a quarter turn.
  7. Turn the heating on and let the radiator warm up. Measure the flow temperature on the pipe at the manual or thermostatic valve side and the return temperature on the pipe at the lockshield side. Open or close the lockshield a quarter turn at a time until the difference between the two readings is about 12°C. A difference near 12°C means the radiator is taking the right amount of heat from the water.
  8. Repeat for each radiator in heating order, opening each lockshield a little more than the last, since each radiator further from the boiler needs more flow. The final radiator on your list, furthest from the boiler, should have its lockshield valve fully open.

Lockshield valves are sensitive, so make small adjustments and wait a few minutes for the reading to settle before adjusting again. If a radiator gets hotter than the fully open ones, close its lockshield a little. If one is not as hot as the others, open it a little more. Expect to go round the house more than once before the system settles.

What if a radiator still stays cold?

Check both valves are open and bleed the radiator again. If the bottom of the radiator stays cold while the top is hot, sludge has settled inside and the radiator needs a flush, which is a job for a heating engineer. If a thermostatic valve will not open, its pin may be stuck: remove the TRV head and press the pin gently with a small tool. If the boiler pressure keeps falling below 1 bar, stop and call an engineer, since the system may be losing water. Balancing only fixes uneven flow; it cannot fix air, sludge, a stuck valve or a leak.

How much does professional balancing cost?

A professional balancing job typically costs in the region of £100 to £250, with the work taking up to half a day. That is worth paying when the system has many radiators, when radiators stay cold after your own attempt, or when the boiler pressure keeps dropping. For a small house with a handful of radiators, the do-it-yourself method above covers the same ground for the price of a thermometer. If you are sizing radiators for a room, our Radiator Size Calculator gives the size from the room volume, and our Boiler Size Calculator gives the boiler size in kW.

How often should you balance radiators?

Balance the system when you move into a home, after adding or removing a radiator, after a boiler change, or whenever rooms start heating unevenly. Bleed the radiators first each autumn when the heating goes back on, since bleeding alone fixes many cold radiators and is quicker than a full balance. A system that heats evenly and holds its pressure needs no regular rebalancing.

Frequently asked questions

What does balancing a radiator mean?

Adjusting the lockshield valve to control how much hot water flows through each radiator, so heat spreads evenly instead of favouring the radiators nearest the boiler.

What is the 12°C rule for balancing radiators?

The target difference between the flow pipe and the return pipe on a radiator. A difference near 12°C means the radiator is taking the right amount of heat from the water as it passes through.

Which valve do I turn to balance a radiator?

The lockshield valve, usually under a plastic cap on the opposite side from the thermostatic or manual valve. Turn it clockwise to close and anti-clockwise to open, a quarter turn at a time.

Can I balance radiators myself?

Yes, with a bleed key, a spanner and a thermometer. Call a heating engineer if radiators stay cold after balancing, if the boiler pressure keeps dropping, or if you suspect sludge in the system.

Sources

The step-by-step lockshield method, the quarter-turn adjustment, the 12°C flow-to-return target and the fully open final radiator follow published UK radiator balancing guides from Hometree, ServiceTeam, Housewarm and Ageas. The 1 to 1.5 bar boiler pressure check and the quick test of closing hot radiator valves follow a UK heating engineer guide. The £100 to £250 professional cost follows a UK heating service guide.

Changelog

  • 8 November 2026: guide published.

Leave a Comment