Snow depth, snow type and roof area to the roof load in pounds per square foot, the total weight on the roof and the share of your design load.
24 inches of wet snow puts 40.8 pounds per square foot on a roof. On a 1,500 square foot roof that is 61,200 pounds in total. Against a 30 psf design load, that is 136 percent of capacity, which means the load is past the design figure. If you want the number for your own roof, the calculator above gives it from snow depth, snow type, roof area and design load.
How the pounds per square foot figures work
Published snow load guides convert snow depth to load using a rate per inch of depth that depends on the snow type. Fresh snow is the lightest, settled snow is denser, wet snow is denser again, and ice is the heaviest of all. The rates used here are rounded to one decimal place, as published guides present them, so every result is an estimate, not a structural assessment. Multiply the rate by the depth in inches to get the load in pounds per square foot.
| Snow type | Load per inch of depth |
|---|---|
| Fresh snow | 0.5 psf |
| Settled snow | 1.3 psf |
| Wet snow | 1.7 psf |
| Ice | 4.8 psf |
Worked example: 24 inches of wet snow
The snow type is wet, so the rate is 1.7 psf per inch. Depth is 24 inches, so the load is 24 × 1.7 = 40.8 psf. Roof area is 1,500 square feet, so the total weight is 40.8 × 1,500 = 61,200 pounds, which is about 30.6 US tons. Against a 30 psf design load, the share is 40.8 ÷ 30 × 100 = 136 percent, so the load is past the design figure and the roof needs professional attention rather than a wait for the next thaw.
Comparing a load with a design load
A design load is the snow load a roof was built to carry, and it varies by locality because building codes set it from local snowfall records. Your local building department can tell you the design load that applies to your home. The table below shows how the worked example load of 40.8 psf compares with the three design loads in the calculator.
| Design load | 40.8 psf as a share | Reading |
|---|---|---|
| 20 psf | 204% | Well past the design figure |
| 30 psf | 136% | Past the design figure |
| 40 psf | 102% | Just past the design figure |
How to measure snow depth without going on the roof
Never climb on a roof to measure snow. A snow-covered roof is slippery, and a person standing on a loaded roof adds weight to the structure that is already under strain. Measure the depth on the ground, away from drifts, with a ruler or a yardstick pushed down to the ground surface, and use that figure. Drifts pile snow far deeper in some spots than in others, so a ground measurement is a guide to the general cover, not a reading of the deepest drift. If the calculator shows a load near or past your design load, or if you see sagging, hear creaking, or find doors and windows starting to stick, call a roofing contractor or a structural engineer and keep people out from under the roof edge. Clearing a loaded roof is work for professionals with the right equipment, not a ladder job.
What this estimate leaves out
The calculator assumes an even cover of one snow type across the whole roof area. Real roofs gather drifts against parapets, valleys and chimneys, and a pitched roof sheds snow while a flat roof holds it, so the true load varies across the surface. Rain falling on snow adds weight fast, and repeated freeze and thaw cycles turn snow into ice, which is why an old cover weighs more per inch than fresh snow. Treat the result as a planning figure that tells you whether to seek professional advice, not as a verdict on whether a roof will hold.
Frequently asked questions
How much does 24 inches of wet snow weigh on a roof?
At 1.7 psf per inch, 24 inches of wet snow is 40.8 pounds per square foot. On a 1,500 square foot roof that is 61,200 pounds in total. Against a 30 psf design load that is 136 percent of capacity.
How do I find my roof design load?
Ask your local building department, since design loads are set from local snowfall records and vary by locality. Building codes for your area carry the figure, and a structural engineer can confirm it for an older home.
Should I climb on the roof to measure snow depth?
No. A snow-covered roof is slippery, and your weight adds to a structure already under strain. Measure on the ground away from drifts and use that figure in the calculator.
What should I do if the load is past the design load?
Call a roofing contractor or a structural engineer, keep people out from under the roof edge, and watch for sagging, creaking or sticking doors and windows. Clearing a loaded roof is professional work, not a ladder job.
Sources
The per-inch rates of 0.5, 1.3, 1.7 and 4.8 psf for fresh, settled and wet snow and ice follow published snow load guides, which present them rounded to one decimal place. The design-load comparison follows the local-code approach those guides describe: design loads vary by locality and the local building department holds the applicable figure. The total weight is load per square foot multiplied by roof area, and the share is load divided by design load multiplied by 100.
Changelog
- 3 November 2026: calculator published.
Cite this page
APA: Wolveyes. (2026, November 3). Snow Load Calculator. Wolveyes. https://wolveyes.pk/calculators/snow-load-calculator/
MLA: “Snow Load Calculator.” Wolveyes, 3 Nov. 2026, https://wolveyes.pk/calculators/snow-load-calculator/
<iframe src="https://wolveyes.pk/calculators/snow-load-calculator/" width="100%" height="600" style="border:1px solid #E5E0D5;border-radius:8px;" title="Snow Load Calculator by Wolveyes"></iframe>
<p><a href="https://wolveyes.pk/calculators/snow-load-calculator/">Snow Load Calculator by Wolveyes</a></p>