Printer type, hours per print, prints a week and your electricity rate to the cost per print, per week, per month and per year of running a 3D printer.
An 80W open-frame FDM printer running a 5 hour PLA print costs about £0.11 a print in electricity at the Ofgem rate of 26.32p per kWh: it uses 0.40 kWh a print, and 0.40 kWh times 26.32p is about £0.11. Three prints a week come to about £0.32, a month to about £1.37 and a year to about £16.42. A 250W enclosed printer running an 8 hour ABS print costs about £0.53 a print. Your own cost depends on the printer type, the hours per print, the prints a week and the rate, so enter those numbers in the calculator above.
How much does a 3D printer cost to run per hour?
It depends on the printer type and the material, since the heated bed takes most of the power. The table below uses the Ofgem rate of 26.32p per kWh. An 80W printer on PLA costs about 2p an hour, a 250W enclosed printer on ABS about 7p an hour, and a 450W printer with the chamber heater on about 12p an hour. The first hour draws more than the average while the bed and nozzle heat up, then the draw settles for the rest of the print.
| Printer | Power | Energy per print | Cost per print | Cost per month | Cost per year |
|---|---|---|---|---|---|
| Open-frame FDM, PLA, 5 hour print, 3 a week | 80W | 0.40 kWh | £0.11 | £1.37 | £16.42 |
| Open-frame FDM, PLA, 2 hour print, 5 a week | 80W | 0.16 kWh | £0.04 | £0.91 | £10.95 |
| Enclosed FDM, ABS, 8 hour print, 2 a week | 250W | 2.00 kWh | £0.53 | £4.56 | £54.75 |
| Enclosed FDM, chamber on, 10 hour print, 1 a week | 450W | 4.50 kWh | £1.18 | £5.13 | £61.59 |
Check the table against the calculator: an 80W printer running a 5 hour print uses 0.40 kWh a print, which costs about £0.11 a print and about £1.37 a month at 3 prints a week. A 250W enclosed printer running an 8 hour print uses 2.00 kWh a print and costs about £0.53 a print. A 450W printer with the chamber heater on uses 4.50 kWh for a 10 hour print and costs about £1.18 a print. Over a year, the PLA printer costs about £16.42, the ABS printer about £54.75 and the chamber printer about £61.59.
How much does a 3D printer cost to run per year?
Far less than most people expect, if you count the electricity alone. An 80W printer running 5 hour prints, 3 times a week, uses about 62.4 kWh a year, which costs about £16.42 at the Ofgem rate. A 250W enclosed printer running 8 hour prints twice a week uses about 208 kWh a year and costs about £54.75. The electricity is the smallest of the three running costs, though. Filament costs more than the power: PLA at about $20 a kilogram is about 2 cents a gram, and a printer laying down about 15 g an hour spends about 30 cents an hour on plastic. Machine wear adds more: a $400 printer spread over 5,000 print hours costs about 8 cents an hour. Put together, one printer hour runs about $0.39 before the cost of failed prints.
Does the material change the cost?
Yes, because hotter materials need a hotter bed and nozzle, and the bed takes most of the power. PLA prints cool, so an open-frame printer averages about 80W on PLA. ABS needs more heat, so the same style of printer averages about 120W on ABS, which works out to about £0.16 for a 5 hour print. An enclosed printer on ABS averages about 250W, and with the chamber heater on it reaches about 450W. Resin printers are a different case: they use a light source rather than a heated bed, so they draw far less power while printing, but the calculator here covers FDM printers, which are the common home machines. If you can print a part in PLA instead of ABS, the electricity drops by about two thirds for the same print time.
How to cut the cost of running a 3D printer
Print in PLA where the part allows it, since PLA runs cooler than ABS and costs about a third of the power for the same print time. Batch small parts onto one plate instead of printing them one at a time, so the bed heats once for several parts. Lower the bed temperature where the material allows it, since the bed is the biggest draw. Switch the printer off at the wall when it is done: some printers never sleep, and one model draws about 22W around the clock, about 16 kWh a month, about £4.21 at UK rates, for doing nothing. Keep the printer in a warm room in winter, since a cold room makes the bed work harder to hold its temperature. None of these change the filament cost, which is the bigger bill, but they keep the electricity part down to pennies a print.
What does it cost in the US?
The same maths applies with the US average rate of about 18 cents per kWh. An 80W printer running a 5 hour PLA print costs about $0.07 a print at that rate. Three prints a week come to about $0.22, a month to about $0.94 and a year to about $11.23. A 250W enclosed printer running an 8 hour ABS print costs about $0.36 a print at the US rate. Owner measurements put typical home filament printers at roughly 100W to 200W while printing, which is about 1.8 to 3.6 cents of electricity per print hour at the US average. Enter your own rate in the calculator if your tariff is higher or lower than the average.
Frequently asked questions
How much does a 3D printer cost to run per hour?
About 2p an hour for an 80W printer on PLA at the Ofgem rate of 26.32p per kWh, about 7p an hour for a 250W enclosed printer on ABS, and about 12p an hour with the chamber heater on.
How much electricity does a 3D printer use per print?
An 80W printer running a 5 hour print uses about 0.40 kWh, about 11p. A 250W enclosed printer running an 8 hour print uses about 2.00 kWh, about 53p.
Does a 3D printer use a lot of electricity?
No. A typical home printer costs about £16 to £55 a year in electricity at UK rates, depending on the printer and how often it prints. Filament costs more than the power.
What costs more: the electricity or the filament?
The filament. PLA at about $20 a kilogram is about 2 cents a gram, and about 15 g an hour works out to about 30 cents an hour, against about 2 cents an hour of electricity for an 80W printer.
Sources
The average draws of about 80W for PLA, about 120W for ABS, about 250W for enclosed ABS and about 450W with the chamber heater on, and the US residential average of about 17.47 cents per kWh, follow a 3D printer electricity guide updated in July 2026 from manufacturer measurements. The owner measurements of a Bambu Lab A1 at 90W to 130W while printing, a Creality K2 Plus at 180W to 200W, the 22W idle draw and the 16 kWh a month figure of about $3.01, and the typical home range of 100W to 200W while printing, follow a 3D printer cost guide updated in October 2026. The Bambu Lab figures of 80W for the A1 mini, 95W for the A1, 105W for the P1S and 200W for the P2S, the running cost of about 17 cents per print hour including wear, and the EIA figure of 18.31 cents per kWh for July 2026 follow a 3D printing cost guide updated in October 2026. The wear figure of 8 cents an hour for a $400 printer over 5,000 hours, the filament figure of about 30 cents an hour at $20 a kilogram and 15 g an hour, and the combined figure of about $0.39 a printer hour follow a 3D printer cost guide updated in November 2026, which puts the EIA average at 17.3 cents per kWh for 2025 and 18.2 cents forecast for 2026. The 26.32p per kWh rate is the Ofgem Great Britain average Direct Debit electricity rate under the price cap for 1 October to 31 December 2026. The US rate of about 18 cents per kWh follows the US Energy Information Administration average for August 2026.
Changelog
- 19 November 2026: calculator published.
Cite this page
APA: Wolveyes. (2026, November 19). 3D Printer Cost Calculator. Wolveyes. https://wolveyes.pk/calculators/3d-printer-cost-calculator/
MLA: “3D Printer Cost Calculator.” Wolveyes, 19 Nov. 2026, https://wolveyes.pk/calculators/3d-printer-cost-calculator/
<iframe src="https://wolveyes.pk/calculators/3d-printer-cost-calculator/" width="100%" height="600" style="border:1px solid #E5E0D5;border-radius:8px;" title="3D Printer Cost Calculator by Wolveyes"></iframe>
<p><a href="https://wolveyes.pk/calculators/3d-printer-cost-calculator/">3D Printer Cost Calculator by Wolveyes</a></p>