A radiator that is hot at the top and cold at the bottom almost always has sludge sitting in its lower channels. The sludge is magnetite, a black iron oxide that forms as the steel in the radiators and the iron in older pipework corrode, and because it is heavier than water it sinks and settles where the flow is slowest: the bottom of the radiator. Once it builds up, hot water flows across the top of the radiator and never reaches the lower half, so the bottom stays cold while the top warms up. Bleeding will not fix it, because bleeding removes air, and air rises to the top. The fix is to flush the sludge out, either by taking the radiator off and hosing it through, or by getting the whole system flushed by a heating engineer.
What does hot at the top and cold at the bottom mean?
The pattern tells you where the problem is. In a working radiator, hot water enters at one top corner, travels across the radiator and leaves at the opposite bottom corner, so the whole surface warms evenly. If the bottom stays cold while the top is hot, the hot water is entering but cannot circulate through the lower half. One boiler maker puts it plainly: the culprit in 99% of these cases is a build-up of sludge and grime. The pattern also rules out the look-alikes: a radiator that is cold only at the top has trapped air, and that one you can bleed. A radiator that is cold all over has a stuck valve or a balancing problem, not sludge. A radiator that is cold at the bottom and hot at the top, with warm pipes at both valves, points to sludge inside that radiator.
How to confirm sludge in 20 minutes
Run this check before you touch anything. Turn the heating on and wait about 20 minutes, long enough for the whole system to come up to temperature. Then run your hand slowly up the radiator from the bottom: it should warm evenly, and a sharp change from cold to hot part way up is the sludge line. Feel the two pipes at the valves as well: warm pipes with a cold lower half point to sludge inside the radiator. Then walk the house. One cold-bottomed radiator means the problem is local to that radiator. Several cold-bottomed radiators, or the coldest ones furthest from the boiler, mean the sludge is in the whole system. As a final check, bleed the radiator with the heating off and the radiator cool, and read the water: brown or black water is the sludge confirming itself. After bleeding, check the boiler pressure gauge and top it up to the level the maker gives if it has dropped. Do not turn the thermostat up to compensate: it fixes nothing and only raises the bill.
How to fix a single radiator yourself
If only one radiator is affected, you can take it off and flush it out by hand. It is a reasonable job for a careful DIYer, with two cautions: never fully undo the valves, or you may drain the whole system, and on a sealed system the boiler usually needs repressurising afterwards. If that sounds like more than you want to take on, it is a short visit for a plumber.
- Turn the heating off and let the radiator cool down completely. Working on a hot radiator is a scalding risk, and the system must be cool before you open it.
- Isolate the radiator. Close the thermostatic valve on one side and the lockshield valve on the other. Count how many turns it takes to close the lockshield valve, and note the setting on the thermostatic valve, so you can put both back exactly where they were.
- Drain the radiator. Put a large tray under the swivel nut on the inlet pipe, undo the nut, then open the bleed valve at the top of the radiator so the water can run out.
- Remove the radiator. Undo the other swivel nut on the outlet pipe and lift the radiator off its wall mounts. Expect it to be heavy: a radiator full of sludge weighs far more than an empty one.
- Flush it outside. Take the radiator outside, hold a garden hose tightly into one inlet and run the water through on high pressure until it comes out clear from the other side, then flush it back the other way. Tapping it with a rubber mallet helps shift stubborn sludge.
- Refit, refill and bleed. Put the radiator back on its mounts, reconnect both valves, reopen them to the settings you noted, then refill the system, bleed the radiator and check the boiler pressure. Top the pressure up to the maker level if needed.
When to get a professional flush
If several radiators are cold at the bottom, the sludge is in the whole system, and a single-radiator flush will not fix it. The options are a chemical flush or a power flush, and both are jobs for a competent and suitably qualified heating engineer. In a chemical flush, a cleaner is added to the system water and circulated for several hours or up to a day, then the whole system is drained and refilled. In a power flush, the engineer flushes water and chemical cleaners through the system under pressure. A power flush typically costs $150 to $600 depending on the number of radiators, for a 4 to 8 hour job, and is usually needed every 5 to 6 years. Ask for a corrosion inhibitor and a magnetic filter at the same visit: the inhibitor slows new sludge forming, and the filter catches it before it settles.
How to stop sludge coming back
Sludge is a sign of a system that lacks corrosion protection. If the water in the system has not been treated with a suitable inhibitor, or if the system has been drained and refilled without adding inhibitor, corrosion will continue. After any flush, add inhibitor to the system water and fit a magnetic filter on the return pipe to the boiler, which catches iron oxide before it settles in the radiators. Check the inhibitor level when the system is serviced, and top it up after any drain-down. Keep the system pressure at the maker level, since a system that keeps losing pressure keeps taking in fresh oxygenated water, which feeds corrosion. A system that is flushed, treated and filtered stays clear for years; a system that is only flushed will sludge up again.
For the radiator jobs that go with this one, see our guide to bleeding a radiator for the cold-top problem, our guide to balancing radiators for radiators that heat unevenly across the house, our radiator size calculator if a radiator is too small for its room, and our boiler size calculator if the whole system is underpowered.
Frequently asked questions
Why is my radiator hot at the top but cold at the bottom?
Sludge, almost always. Magnetite, a black iron oxide from corrosion inside the system, settles in the lower channels of the radiator and blocks the hot water from reaching the bottom. One boiler maker puts sludge behind 99% of these cases.
Will bleeding fix a radiator that is cold at the bottom?
No. Bleeding removes air, and air rises, so bleeding fixes a radiator that is cold at the top. A cold bottom is the opposite signal: something heavy sitting inside, which no amount of bleeding will remove.
How much does a power flush cost?
Typically $150 to $600 depending on the number of radiators, for a 4 to 8 hour job, every 5 to 6 years. A single radiator can be flushed by hand for nothing but time, by taking it off and hosing it through outside.
How do I stop sludge coming back?
Add a corrosion inhibitor to the system water after any flush, and fit a magnetic filter on the return pipe to the boiler. Check the inhibitor at each service, and keep the system pressure at the maker level so fresh oxygenated water does not keep entering.
Sources
The magnetite sludge cause, the pattern of hot water entering at the top and failing to reach the lower half, and the chemical flush method of circulating a cleaner for several hours to a day before draining follow a 2026 radiator cold-bottom repair guide. The manual flush steps of closing both valves, counting the lockshield turns, draining, removing the radiator and hosing it through until the water runs clear, the warning that bleeding will not help a cold bottom, and the chemical flush and power flush options follow a UK radiator cold-bottom guide. The diagnosis of one radiator meaning a local problem and several meaning a system-wide problem, the stuck thermostatic valve and balancing causes, and the inhibitor and magnetic filter prevention follow a 2026 radiator heating guide. The 20-minute hand test, the brown or black bleed water check, the warning never to turn up the thermostat to compensate, the power flush figures of $150 to $600 for a 4 to 8 hour job every 5 to 6 years, and the boiler maker quote that sludge is the culprit in 99% of cases follow a 2026 radiator cold-bottom guide.
Changelog
- 20 November 2026: guide published.