How to Draught-Proof Your Home

Home › Guides › How to Draught-Proof Your Home

Start with the doors and the windows, since those are the biggest draughts in most homes, then work through the letterbox, the keyhole, the floors, the loft hatch and any unused chimney. Draught-proofing a typical gas-heated semi-detached home saves around £30 to £45 a year on heating bills according to published UK energy advice, and a chimney draught excluder adds around £90 a year on its own according to one supplier guide. Actual savings vary by home size, heating system and how leaky the home was to begin with.

How to find the draughts

Walk the house on a cold, windy day and hold the back of your hand near the edges of doors and windows, the letterbox, the keyhole, skirting boards, the loft hatch and any fireplace. Cold air on your hand marks a draught. A strip of tissue paper held near a gap moves in a draught too, which helps for gaps too small to feel. Check every external door and every window, including ones that are rarely opened, and check upstairs as well as downstairs, since warm air rises and escapes through gaps at the top of the house. Note each draught as you find it, so you can buy the right strips in one trip.

Doors: the biggest single draught

Fit a brush strip or a rubber seal to the bottom of each external door, and self-adhesive foam strips around the frame where the door meets it. Close the door on a strip of paper: if the paper slides out with no resistance, the seal is too loose there. Fit a keyhole cover and a letterbox brush or flap, since both let in a steady draught all winter. Internal doors to unheated rooms, such as a garage or a conservatory, are worth sealing too, but leave a small gap under internal doors between heated rooms so air can still move around the house.

Windows: foam strips, brush strips and sash windows

For casement windows that open outward on hinges, self-adhesive foam strips pressed into the frame close the gap when the window shuts. Measure the gap first, since foam that is too thick stops the window closing and foam that is too thin leaves the draught. For sash windows that slide up and down, brush strips fitted into the sliding channels seal the gap without stopping the window moving, and a sash window kit with brush strips for the meeting rail covers the middle gap where the two sashes meet. Secondary glazing, a clear panel fitted inside the existing window, cuts draughts further and is a bigger job than strips, so it suits windows that stay shut all winter. Replace cracked putty and perished seals before fitting strips, since a strip cannot seal a frame that is falling apart.

Letterbox, keyhole, floors and skirting

A letterbox brush or an internal flap stops the slot acting as a vent, and a keyhole cover costs a few pounds and takes a minute to fit. For floors, fill gaps between floorboards with a flexible filler or purpose-made strips, since rigid filler cracks as boards move with the seasons. A rug over a draughty floor helps comfort but does not seal the gaps. Seal the joint where skirting boards meet the floor and the wall with caulk, and check where pipes pass through floors and walls, since those holes carry draughts between rooms and from outside.

Loft hatch and unused chimneys

The loft hatch is a large hole in the ceiling of the top floor, and warm air pours through it. Fit foam strips around the hatch frame and fix insulation to the top of the hatch itself, so the hatch matches the insulation around it. For a chimney that is never used, a chimney balloon or a chimney sheep pushed up into the flue blocks the draught, and both come out again when the chimney is needed. Only block a chimney that is truly out of use: a chimney serving a fire or a stove must stay open, and any balloon or sheep must be removed before lighting a fire. Mark a blocked chimney clearly, so nobody lights a fire in it by mistake.

What never to block

Never block a boiler flue, an air brick, a trickle vent or an extractor fan. Boiler flues carry exhaust gases out of the house, and blocking one risks carbon monoxide building up indoors. Air bricks and trickle vents give rooms the fresh air they need, and blocking them traps moisture, which leads to damp and mould. Extractor fans in kitchens and bathrooms remove steam at source, and blocking them sends that moisture into the walls and ceilings instead. If a vent feels like an icy blast, fit a vent cover that still lets air through, or ask a heating engineer whether the ventilation can be reduced safely, rather than sealing it yourself. Anything inside the boiler is work for a Gas Safe registered engineer, not a DIY job.

What draught-proofing costs and saves

Most draught-proofing materials cost a few pounds each: foam strips, brush strips, keyhole covers and letterbox brushes are all small purchases, and a chimney balloon or sheep costs a few pounds more. The work is mostly fitting time rather than material cost, and a whole house can usually be done in a weekend. Published UK energy advice puts the saving from draught-proofing a typical gas-heated semi-detached home at around £30 to £45 a year, and one supplier guide puts the saving from a chimney draught excluder alone at around £90 a year. Your saving depends on how leaky the home was, how large it is, and what you pay for heating, so treat these as typical ranges, not promises. The comfort gain is immediate either way: rooms stop feeling cold near doors and windows, and the heating has less cold air to fight.

Once the draughts are sealed, the heating runs less hard for the same warmth. To put a number on the heating itself, see our guide How Much Does It Cost to Run Central Heating? and work out the hourly cost with our Heating Cost Calculator.

Frequently asked questions

Where are the biggest draughts in a home?

External doors and windows are usually the biggest draughts, followed by the letterbox, the keyhole, gaps in floors and skirting, the loft hatch and any unused chimney. Check all of them on a cold, windy day with the back of your hand.

How much does draught-proofing save?

Published UK energy advice puts the saving for a typical gas-heated semi-detached home at around £30 to £45 a year, and one supplier guide puts a chimney draught excluder alone at around £90 a year. Actual savings vary by home size, heating system and how leaky the home was.

Can I block a chimney to stop a draught?

Only a chimney that is never used, and only with a removable balloon or sheep that comes out before any fire is lit. A chimney serving a fire or stove must stay open, and a blocked chimney should be marked clearly so nobody lights a fire in it by mistake.

What should I never draught-proof?

Never block a boiler flue, an air brick, a trickle vent or an extractor fan. Boiler flues carry exhaust gases out, and vents and fans keep fresh air moving and moisture down. Blocking them risks carbon monoxide build-up, damp and mould.

Sources

The £30 to £45 a year range for draught-proofing a typical gas-heated semi-detached home and the around £90 a year figure for a chimney draught excluder come from published UK energy advice and supplier guides, stated here as typical ranges because savings vary by home. The never-block list follows UK gas safety and ventilation guidance: boiler flues, air bricks, trickle vents and extractor fans must stay clear. The fitting methods for foam strips, brush strips, sash kits, chimney balloons and chimney sheep follow published UK DIY guides, which agree on these points.

Changelog

  • 3 November 2026: guide published.

Leave a Comment