How to Protect Outdoor Taps From Frost

Home › Guides › How to Protect Outdoor Taps From Frost

Disconnect every hose, shut off the indoor valve that feeds the outdoor tap, open the tap to drain the line, leave the tap open for winter, then fit an insulated cover over the tap. Do it before the first hard frost, when night temperatures start falling to freezing. That sequence, in that order, is what protects an outdoor tap: the cover alone cannot save a line that is still full of water.

When to winterize an outdoor tap

Winterize before temperatures regularly drop to 32 degrees Fahrenheit, or 0 degrees Celsius. In many regions that means early autumn, and in colder regions it can mean September. A single hard frost can split a tap or a pipe, and the damage often shows up only when the water is turned back on in spring, as a leak inside the wall. If a forecast shows a hard frost tonight and the taps are not yet done, disconnecting the hoses and draining the lines tonight matters more than waiting for covers to arrive.

Step 1: disconnect hoses and attachments

Remove every hose, splitter, timer and spray attachment from each outdoor tap. A connected hose traps water in the tap body and in the pipe leading into the wall, even when the tap is turned off, and it defeats the drain-down that frost-free taps rely on. Drain each hose fully, coil it, and store it indoors for winter. Check every tap around the house, including ones at the back and side that are easy to forget, and count them before buying covers so each tap gets one.

Step 2: shut off the indoor valve and drain the line

Find the dedicated shut-off valve inside the house for the outdoor line, usually in a basement, crawl space or utility room on the wall opposite the tap. Turn it clockwise until it stops, or turn a lever handle until it sits across the pipe. Then go outside, open the tap fully and let the water trapped between the indoor valve and the tap drain out, with a bucket underneath to catch it. Leave the tap open for winter, so any slow drip or condensation has somewhere to go instead of building pressure in the line. This drained line is the main protection: an empty pipe cannot burst from expanding ice.

Step 3: fit an insulated tap cover

With the line drained, fit an insulated cover over the tap. Foam dome covers and fabric pouch covers both work by trapping a pocket of still air around the tap and holding warmth from the wall, and both usually cost a few pounds or dollars each. Place the cover over the whole tap, pull it tight against the wall with its drawstring, strap or loop, and check that no part of the tap or pipe sticks out. A loose cover that gaps at the wall lets cold air straight in and gives little protection. Keep the cover on until night temperatures stay above freezing in spring, and close the tap before turning the indoor valve back on.

Frost-free taps still need care

A frost-free sillcock puts its shut-off valve several inches inside the heated wall, so the water stops well away from the cold. That design helps, but it does not remove the need for care: a hose left connected holds water against the valve seat and defeats the mechanism, and the tap body itself still sits outside. Disconnect the hose, and fit a cover in cold climates even on a frost-free tap. If your home has no dedicated indoor shut-off valve for the outdoor line, the cover becomes your main defence, so fit it well and check it after storms, and consider asking a plumber about adding a shut-off valve before the next winter.

If a tap is already frozen

Work gently and never force a frozen tap handle, since that can snap the valve. Wrap the tap and any exposed pipe in towels soaked in warm water, replacing them as they cool, and let the ice melt slowly. Check for leaks as it thaws: a split pipe may only show once water flows again. If water appears inside the wall, or the pipe has visibly split, turn off the indoor valve and call a plumber rather than trying to seal a burst pipe yourself. Heat tape on exposed pipes is an option for very cold regions, but it needs a power supply and correct fitting, so follow the maker instructions or have it fitted professionally.

Spring restart checklist

When hard frosts have passed, close each outdoor tap, remove the covers, then turn the indoor valves back on slowly and check each tap and the wall inside for drips. Run each tap briefly to clear the line, then reconnect hoses and check washers and spray attachments for winter damage. A small drip at a tap washer is a cheap fix in spring and a burst pipe in winter, so replace worn washers now rather than leaving them.

Outdoor taps are one part of winter plumbing. For the pipes inside the house, see our guide How to Prevent Pipes From Freezing in Winter and for the whole house, see How to Winterize a House.

Frequently asked questions

How do I protect an outdoor tap from frost?

Disconnect the hose, shut off the indoor valve feeding the tap, open the tap to drain the line, leave the tap open for winter, then fit an insulated cover tight against the wall. Drain the line first: a cover alone cannot protect a line still full of water.

Do I need a cover on a frost-free tap?

Yes, in cold climates. A frost-free sillcock moves the shut-off valve inside the heated wall, but the tap body still sits outside, and a connected hose defeats the mechanism. Disconnect the hose and fit a cover.

When should I winterize outdoor taps?

Before temperatures regularly drop to 32 degrees Fahrenheit, or 0 degrees Celsius. In many regions that is early autumn, and in colder regions it can be September. A single hard frost can split a tap or pipe.

Should I leave the outdoor tap open in winter?

Yes, after shutting off the indoor valve and draining the line. Leaving the tap open lets any slow drip or condensation escape instead of building pressure in the line, and it keeps the line empty.

Sources

The drain-first sequence, hose disconnection and cover fitting follow published plumbing and home improvement guides, which agree that a connected hose traps water in the tap and pipe, that the indoor shut-off and drain-down is the main protection, and that covers trap still air around the tap. Cover prices of a few pounds or dollars each follow retail listings for foam and fabric tap covers. Frost-free sillcock behaviour follows maker and plumbing guidance: the valve sits inside the heated wall, but the tap body remains exposed.

Changelog

  • 4 November 2026: guide published.

Leave a Comment