Switch the heating off and let the radiators cool, open the bleed valve a quarter to half a turn until the hissing stops and water runs in a steady dribble, close the valve, then check the boiler pressure. That is the whole job, and it fixes the classic symptom: a radiator that is cold at the top and warm at the bottom. Trapped air sits at the top of the radiator and blocks hot water from filling it, so bleeding lets the air out and the water in.
First, check that bleeding is the right fix
Turn the heating on, wait for the radiators to warm up, then feel each radiator from top to bottom, with care, since radiators get hot. Cold at the top and warm at the bottom means trapped air, and bleeding should fix it. Cold at the bottom and warm at the top usually means sludge settling in the radiator, and bleeding will not fix that, so it is a job for a heating engineer. Every radiator cold at once usually points to the boiler, the pump or the controls, not to the radiators, so check the boiler display and its manual first.
What you need
- A radiator key, sold at any DIY shop for a few pounds. Some modern valves take a flat screwdriver instead.
- An old towel or cloth and a small bowl or jug to catch drips.
- The boiler manual, for the correct pressure range and the filling loop instructions.
How to bleed a radiator, step by step
- Switch the central heating off and let the radiators cool fully. Bleeding a hot radiator risks scalding from escaping water.
- Find the bleed valve: the small square nut in a round fitting at one of the top corners of the radiator.
- Hold the cloth under the valve and keep the bowl ready.
- Fit the key and turn it anticlockwise, about a quarter to half a turn. You will hear a hiss as air escapes. Do not unscrew the valve fully.
- When water starts to come out in a steady dribble, close the valve by turning it clockwise. Snug, not forced.
- Work through the house one radiator at a time, starting with the radiator furthest from the boiler and moving toward the closest.
- Check the boiler pressure gauge. Bleeding lets out a little water, so pressure on a sealed system can drop. The usual cold range is 1.0 to 1.5 bar. If it has dropped below the range in your manual, top it up through the filling loop exactly as the manual shows.
- Switch the heating back on and check each radiator warms all the way to the top.
After bleeding: what to watch for
A radiator that needs bleeding every few weeks, a boiler that keeps losing pressure, or a bleed valve that leaks after you close it all point to a fault such as a leak, and that needs a heating engineer rather than another bleed. Anything inside the boiler is work for a Gas Safe registered engineer, not a DIY job. If you smell gas, leave the property, do not switch lights on or off, and call the National Gas Emergency number on 0800 111 999.
How often should you bleed radiators
Once a year is enough for most homes, done in autumn before the heavy winter months, when the heating is switched back on after months off. Bleeding at the start of winter also catches air that entered during summer maintenance. Radiators that gurgle or develop a cold top mid-winter can be bled again at any time, using the same steps, with the pressure check at the end each time.
If the radiator is the wrong size for the room rather than full of air, size it first with our Radiator Size Calculator. For the full winter preparation list, see our guide How to Winterize a House.
Frequently asked questions
How do I know if a radiator needs bleeding?
Feel it from top to bottom once the heating has warmed up. Cold at the top and warm at the bottom means trapped air, and bleeding should fix it. Cold at the bottom points to sludge, and every radiator cold at once points to the boiler or controls.
Should the heating be on or off when bleeding a radiator?
Off, with the radiators cooled fully. Bleeding a hot radiator risks scalding, and a running system pushes water out with the air. Switch the heating back on only after every radiator is bled and the pressure is checked.
What should boiler pressure read after bleeding radiators?
The usual cold range is 1.0 to 1.5 bar. Bleeding lets out a little water, so pressure can drop below that range on a sealed system. Top it up through the filling loop exactly as your boiler manual shows.
In what order should I bleed radiators?
Start with the radiator furthest from the boiler and work toward the closest, one at a time. The furthest radiator usually holds the most air, and this order keeps the system balanced as you go.
Sources
The steps, the furthest-from-boiler order, the 1.0 to 1.5 bar cold pressure range and the cold-top versus cold-bottom diagnosis follow published bleeding guides from boiler makers and UK councils, which agree on these points. The Gas Safe rule for boiler internals and the National Gas Emergency number 0800 111 999 follow UK gas safety guidance.
Changelog
- 2 November 2026: guide published.